Hi All, I'm running MM Caster/Camber plates and their front track pack springs on Koni Yellows with an Eibach front anti-rollbar. Rather stiff setup. I was getting ready to install my bump steer kit and found the upper strut mount bearing blown up. Is this from a misalignment during initial...

Would anyone happen to have a point cloud of the S197 suspension points? I would like to model the S197 in susprog or lotus shark to get some data to play with but I haven't been able to find anyone who's measured out the car. I currently don't have the time nor the space to do it to mine.

I am trying to sort thru the massive amount of info on here about springs, and it has brought me to this question. We have L, KA, PA (P spring shows as discontinued). Consensus here seems to be that for a multi use Street/Autocross/4 day year track event car, P springs are a solid answer...

Hey guys,I took a brief hiatus from car stuff while I pursued some other hobbies, and finally said "screw it" and got pretty much a whole suspension overhaul, minus sway bars, and took to installing it today. My brother and I, both definitely amateur mechanics, spent about 8 hours today...

Hi all my 2012 GT is coming up on 150k and I have decided to park it to tackle much needed preventive maintence and do some upgrades.So far here is my shopping list, mind you suspension is currently full stock and I do street the car a lot as it is my part time daily.Out front: Prothane...

Hey, all! Hope everyone is well, and hope your lap times are faster! Got a little preoccupied with work and school, so I haven't been as active on here as I would have liked to have been, but I'm ready to start spending some money on car stuff again.Just FYI, this will be a little long winded...

Recently installed the Cortex LCAs and Relocation brackets. Seen in the instructions about optional welding them in. Says it is a must for drag racing. I autocross and estimate about 400WHP. Will it be fine the way it is or should I have a shop weld it?

I have a 2013 5.0 with a very loud exhaust. Not quite straight piped loud, but quite loud at anything above 30% throttle. It sounds great at WOT, but being that it’s a daily driver, I’d like it to be quieter when I’m just trying to take off from stoplights and such. So I’m looking at quieting it...

Went and found a second region to run autocross with. Southern Indiana Region guys. First time out at their place today. Little different flow than I was used to but it went well.At Rantoul, we normally start first car off at 9:30 and do a morning heat of 5 runs. Then the afternoon we would...

We have (2) used Ford Performance Road Race Oil Pans for sale. They both came out of a Gen 2 motors in S550s. Local Pick up or free shipping to the lower 48 states. $850 each or best offer.

Do pardon my naivety on this subject, but stickers? I have spent a lot of time on this page over the last couple of weeks, and I have seen a TON of truly incredible cars, lots of which that have a bunch of stickers. I've kinda fallen in love with this look so I decided instead of trying to...

Hello everyone! I have been on this site about a million times trying to learn the ins and outs of suspension and the parts that make mustangs handle really well, and then I decided to finally make an account and ask some questions for myself. For some context, I am a college student that has...

Hey guys,I'm looking at installing some cloth Recaro Pole Position seats in my 2013 Mustang GT. I've done a lot of research on making sure I don't get an airbag light after everything is fully installed, but still have some questions I cannot find answers to. I'm hoping one of you that has...

I know its a stretch, but I am on a hunt for a triple pillar gauge pod for a 2012 Boss 302. Looking for the charcoal finish. As far as I can tell Speed of Sound does not make this anymore, so if anyone has one that they would like to sell please let me know. I'm not a fan of the autometer one...

Selling both Flowmaster Outlaw and American Thunder Axlebacks for S197.Both were bought used this year but I didn't even put on the Outlaws and only tried the American Thunders for a week. Ended up getting Borla S Type. Both are in great physical condition, although the black paint American...

2012 Mustang GTEngine: •Boss 302 intake manifold •BBK 85mm throttle body •Airaid intake •Off road x pipe •Bama Tune •Deleted resonators •Deleted mufflers •Quad Tips •JLT oil catch cans passenger & driver •Boss 302 oil coolerSuspension: •Koni sport yellow adjustable struts •BMR...

This is the Build Thread for S197 #406. Reply below.

Hello Everyone,I have some lightly used GLOC pads with barely any wear so tons of like left. Prices include shipping and PayPal fees (USD)GLOC R8 2013-2014 GT500 Front Brembo $195 GLOC R16 2013-2014 GT500 Front Brembo $215 GLOC R8 S197 Rear pads $100PM or email me @...

I hope everyone is staying safe, healthy, and sane right now.I'm selling my set of 4, 18x10 +42 Forgestar F14s in Piano Black to make space for my incoming Apex 18x11s. This is a great set of lightweight, fully rotatable, square setup wheels for the street and/or the track.Asking $900 OBO...

I have been thinking that it is time for a new transmission in my 2013, and I am pretty much deadset on keeping it manual. Or at least I thought I was and then I got to thinking how hard it would be to swap an auto in and mount some paddle shifters in. So my question is, would it be worth or...

All,Since I recently completed the suspension overhaul on my car, the next order of business is finding some replacement tires for my stock 9 year old Pirelli's (would like to actually be able to enjoy the changes I made...). The plan is to eventually move up to a set of Apex EC-7 19x10 square...

End of the year is coming up, and I have decided that I want to start tracking my car. Are there any important suspension upgrades that I should consider doing sooner rather than later? or anything I can do now to help the suspension?

We've had this product available for several years now and have used it on several track cars. It was developed out of necessity so the EPAS could be used whenever applicable.P/N: EPAS-40-1000 (we will be adding it to the website soon but it's not currently there)Description: Electronic...

Hey there, I am a long time lurker of this forum so figured I'd see if any of yall had some suspension stuff around. I've had my 2005 GT for about a year now (bone stock) and have been collecting parts to start building it into a weekend track car (maybe iron spec?) this winter.Im looking...

‼️FOR SALE‼️Less then 1K miles on everythingPrefect working conditionWhipple Gen 3 2.9 Whipple Stage 2132mm Throttle Body with electronicsFuel rails have port for quick disconnect for fuel draining and swapping fuelsNo injectors or BAP10Rib pulley kit with 20% lower3.0/3.25 and...

After tracking my car for 4+ years on the hopes that the FR500S setup (control arms and tie rod ends) had OK bump steer settings, and not having any issues up to that point, I was going through the car before a track day and found a loose ball joint. (Of course it was the Monday before a track...

We carry Watson Racing Products for the S197 and S550 Mustangs. We have a freight order leaving this week to Florida. If any of you are in the area and were interested in any of their products let us know and we can save you on the shipping charges. We have 3 bare 4 point S550 Bars on the way...